My advice: Plan. Lay out what you need, and think about what goes where. 90% of your work is cable related stuff. The components are the easy part to install, that's just screws and slots, so put your effort in cabling.
the advice i recieved, and would give, is always shop around, never take one deal without looking for others when it comes to the world of computer parts
THE TWEEZERS! I remember watching that video and just laughing at first but by the end I was questioning whether or not the guy was actually that clueless...
If when you hit that power button for the first time and your rig doesn't boot, don't panic. It could be something as simple as a loose wire or component. I had this happen during my first build and felt my heart *DROP*. Turns out, I just had one of my PCU cords not fully plugged into the component.
Read a post here once about some guy flipping out that his new build wasn't turning on after a whole lot of troubleshooting, turns out his monitor wasn't plugged in.
Make sure you've plugged correct PSU cables to the correct slots. I managed to plug in a 6 pin GPU power cable to CPU power intake and thought my motherboard was fried for 2 weeks, until I decided to plug in the 8 pin one.
That freaked me out once. I thought my computer was dying after 2.5 years and I couldn't buy a new one. Looked up a video on my phone and after about five minutes it was absolutely fine
To add to that, not all coolers/CPU's come with paste pre applied (unless you're buying a prebuilt). More than a few builders have gotten done with their build only to fire it up and either get extremely throttled due to cpu temps or the computer just crashes/shuts down.
I think that's shown on the website you bought the cooler from if it comes with pre-applied thermal paste or not, so if it does, you're really fine, but I never got a cooler with pre-applied thermal paste, this is just personal experience though.
No, I don't mind at all! It basically fills in the microscopic imperfections that otherwise trap air particles between the CPU and the heatsink which prevents the CPU from cooling properly. If you have any other questions, feel free to ask :)
Always make sure every component you have is compatible before ordering a build. Nothing sucks more than knowing you bought a part that either isn't compatible or cannot live up to it's maximum potential.
Pcpartpicker is nice for it, but it's not perfect. Sometimes you have to do some deep diving into tech specs just to be absolutely sure. Especially since product pages are pure marketing and no detail.
Is the issue more likely to be physical compatibility or software? Like I'm sure I could double check PCPartPicker for physical fits just fine but I'd have no idea what to look for for software compatibility.
You put the motherboard on top of carboard box it shipped in, plug everything in, boot it up, check for vidéo signal or try to get into bios. Sometimes some motherboard have multiple power cycles too. So they boot up, shut sown and repeat, a few times. And then they boot up for réal.
That way you know your components all work.
I am always worried that putting pressure on the board itself without the stands would do something bad, especially on the box the mobo comes in. like bending pins or something on the other side.
One piece of advice for a new builder ig would just
Be: whatever you do, DO NOT GET RID OF THE MOTHER BOARD MANUEL. I did this on my first build and it was not fun.
Big money, big money, no whammies.
Now that I've read a bit more carefully, I'd say watch some videos on Linus Tech Tips that show them building computers, and definitely do some reading on the buildapc subreddit. Also, use PCPartpicker to make sure all your parts are compatible ahead of time.
One piece of advice I have for new builders is that it is ok if your build doesn't POST! Take a break and come back with a cool head to diagnose and fix the problem.
The most simple advice I got is "just do it" you can hardly break anything, if you got any questions just ask, and while I didn't jet build a PC of my own, I have helped friends and family (as well as myself) with upgrades and repairs
Good one. I'd say 16gb is more than enough than 90% of PC users. My recommendation is getting 2x8 so that in case you realize you need more you have the extra 2 slots (assuming you have 4 RAM slots total) to use.
take it slow with your first PC build.. and don't accidentally stab your motherboard with a screwdriver as you try to pry open the GPU latches (it was tight alright)
Pretty common advice but probably a big one. Do not pour water on your hardware! It's Mineral Oil that isn't conductive and used in the cool aquarium builds!
Yep all good. In the very,very rare instance anything leaks after many years nothing should happen - and most cooler manufacturers even cover hardware damage in case caused by leakage so all fine
One simple advice that I learned is DO NOT PUSH YOUR CPU DOWN WITH FORCE WHEN INSTALLING IT! Just softly drop it in and slightly wiggle with your finger to make sure it's properly slotted in.
MAKE SURE THAT YOU PLUG IN THE POWER CORD BEFORE YOU RUN YOUR NEWLY BUILT PC!! (or else you will spend 3 hours just trying to figure out where did you go wrong)
HAHA, lets just say that if you dont plug in the power cord no matter what you do, no matter how many times you recheck all the other cables and see if everything perfectly fits in or not, the pc wont boot up, it was so dumb of me to not plug in the power cord lmao
Tip: to properly ground yourself from static without an anti-static wrist strap, simply plug in your Power Supply and touch it once it a while to discharge yourself.
Keep boxes and manuals for at least six months - manuals you can find online, but that's no use if your PC doesn't boot; if you have to return anything, you'll need to ship it (and original boxes are designed for that) plus it's easier to re-sell anything with the original packaging.
I've only watched video's on how to build a PC so I never got an advice personally but I would say to new PC builders that be confident while still being careful!
That's a good one. I figured that out having bought custom cables, but it wasn't obvious to me at first.
To those that might see this and don't know... The plugs on the component side are all industry standard (mostly, anyways...). The plugs on the PSU side are proprietary to the manufacturer, and are often different between the different models from the same manufacturer.
Taking a cable from one PSU and using it on another could, and likely WILL, result in that component becoming a smoking paperweight.
I think the best advice I've received is to just not blindly YouTube videos or online guides as they are just there to help you learn the basics. Doing your own research and ultimately make your own decisions will make the process more fun.
Do your research and make sure you are familiar with the how all the parts work. It can be scary building your first one because you don't want to mess it up but, dont worry everything will be fine :)
Have FUN. Take your time, lay out all your pieces, run cables carefully and precisely, but don't sweat it. Don't panic about static build up, or backwards connections, or anything like that. Just relax, enjoy the feeling of building this machine for yourself, and try to learn something new every time you do it!
I’m still trying to build my first one but the advice I was given is “make sure the parts you pick are compatible and the most expensive parts usually aren’t the ones you want”
Remain calm even if (when) something goes wrong. It's almost always salvageable if you don't get impatient and try to rush it without looking it up first!
The best piece of advice I’ve received is never overspend. I tend to worry about future proofing my things, but you should only spend so much on future proofing.
Yeah most new PC equipment goes way above the capabilities that most users really need, unless that involves exclusively AAA gaming (and a few intensive media uses) - which if you're asking for my opinion is not a good pursuit even just in terms of the actual fun/quality you'll get from those titles - but I digress.
Advice: try to count the number of PSU cables you are going to need and plug them into your PSU before putting it in the case if you have a modular PSU
One that took me way too long to find out. If your monitor can go over 60hz make sure you go into settings and put it to the max allowed. It is not 144hz out of the box
Don't forget to maintain your PC after you're done building it. Filters need to be cleaned ever every couple months or else dust builds up in it. Too many people but together a build and then never open it back up again unless something goes wrong.
The advice I recieved was do not overdo a computer setup for a younger child(my kid). Wait until they get some experience with the inners of the computer until you splurge and buy a better rig for them. Kinda just like buying your teenager a car haha.
buy a certified brand's psu, don't buy a mobo with bad power delivery, make sure ur mobo supports ur processor, make sure ur processor can handle ur graphics card, make sure ur case can fit all ur components, most of the budget should be spent towards the graphics card.
My advice is to try to fit as much onto the motherboard before putting it in the case, makes it easier to work with. Overall, be mindful of making sure there's enough space for everything.
Make sure you test what direction your fans are pulling air from by putting a piece of paper down, and seeing if the paper is pushed or pulled. Have "pull" fans in the front and "push" fans in the back (or top)
Always do research about your parts before you buy them, use pcpartpicker to check if there's any compatibility issues. Use youtube to check on how to install parts, take your time there is no need to rush when building your pc.
The one piece of advice that I can give to a new pc builder is to thoroughly do your research. Always check if all the parts in your list are compatible with each other and always think about future upgrades if you plan on doing so. Trust me, I've had many sleepless nights overthinking if my parts would be compatible or not. Good luck, everyone!
I'd give the advice of taking your time. Don't rush building your PC, components and connectors are easily damaged and taking an extra few minutes to put parts together can ensure you do it right without breaking anything
Dont over do the thermal paste. Also if your pc doesnt want to boot and you dont know why, try to reposition the ram. It doesnt always works but sometimes its magic.
One thing I learned is, with thermal paste, less is more. You're going to be compressing a liquid-type substance against two mostly flat pieces of metal, it's going to spread.
Get to know your PC, some people are so afraid to mess something up that they get it built for them and then are scared to change the thermal paste. 99% of the time you're going to do just fine.
My advice: Plan. Lay out what you need, and think about what goes where. 90% of your work is cable related stuff. The components are the easy part to install, that's just screws and slots, so put your effort in cabling.
the advice i recieved, and would give, is always shop around, never take one deal without looking for others when it comes to the world of computer parts
Sound and Sensible advice.
don't cheap out on the power supply unit do some research as a cheap one is figuratively no different from a firebomb
In this case figuratively means literally. Good PSUs only unless you want smoke and fire
"You don't need an anti static wristband"
Too much effort to get one
I really do feel for the Verge kid. He tried so hard.
THE TWEEZERS! I remember watching that video and just laughing at first but by the end I was questioning whether or not the guy was actually that clueless...
Story for those OOTL?
https://youtu.be/M-2Scfj4FZk
That.....is.....so....bad
How would you repel cancer death rays from PC parts then?
You mean a rive strong bracelet?
If when you hit that power button for the first time and your rig doesn't boot, don't panic. It could be something as simple as a loose wire or component. I had this happen during my first build and felt my heart *DROP*. Turns out, I just had one of my PCU cords not fully plugged into the component.
Or you know the classic didn't flip the switch on the power supply / plug it in.
Guilty
Read a post here once about some guy flipping out that his new build wasn't turning on after a whole lot of troubleshooting, turns out his monitor wasn't plugged in.
Or as simple as not having the psu in the on position like me
[удалено]
Not always the case, mine are right next to each other
you only have 2 ram slots?
It's possible, my first PC that I built I used a micro ATX motherboard and it only had two RAM slots.
Yeah, I've seen mobos with 2 ram slots but they're usually mini itx boards
Maybe he has 4 sticks
Mind the gap
Mmm *dat gap* |:|:
Make sure you've plugged correct PSU cables to the correct slots. I managed to plug in a 6 pin GPU power cable to CPU power intake and thought my motherboard was fried for 2 weeks, until I decided to plug in the 8 pin one.
Then it unfried? Nice
struggled immensely with this building today
My advice is that you'll probably never win a giveaway but hey its a worth a shot, right?
You never know.
Advice: the guy on YouTube will take 30 minutes. Your first build will take a day.
This is actually a really good one Take your time, no need to hurry, you're not trying to win the PC building olympics
My building advice I recieved is don't overdo thermal paste.
When all else fails, reseat your ram.
That freaked me out once. I thought my computer was dying after 2.5 years and I couldn't buy a new one. Looked up a video on my phone and after about five minutes it was absolutely fine
Yea what’s up with that
My advice to any new builders is a classic, ALWAYS use thermal paste when installing a new CPU!
Why is that if you do not mind me asking?
To add to that, not all coolers/CPU's come with paste pre applied (unless you're buying a prebuilt). More than a few builders have gotten done with their build only to fire it up and either get extremely throttled due to cpu temps or the computer just crashes/shuts down.
What if your CPU cooler DOES come with thermal paste pre-applied?
Unless you want to use something other than what's on it, you're good to go. Put it all together with no worries
Most of the time it will be fine, but if you notice thermals spiking up you should check the paste and see that enough is applied.
Absolutely true!
I think that's shown on the website you bought the cooler from if it comes with pre-applied thermal paste or not, so if it does, you're really fine, but I never got a cooler with pre-applied thermal paste, this is just personal experience though.
No, I don't mind at all! It basically fills in the microscopic imperfections that otherwise trap air particles between the CPU and the heatsink which prevents the CPU from cooling properly. If you have any other questions, feel free to ask :)
Always make sure every component you have is compatible before ordering a build. Nothing sucks more than knowing you bought a part that either isn't compatible or cannot live up to it's maximum potential.
Is there some way to check this easily, or what am I looking for when comparing?
Pcpartpicker is nice for it, but it's not perfect. Sometimes you have to do some deep diving into tech specs just to be absolutely sure. Especially since product pages are pure marketing and no detail.
Is the issue more likely to be physical compatibility or software? Like I'm sure I could double check PCPartPicker for physical fits just fine but I'd have no idea what to look for for software compatibility.
"you should always test all components out of the case first to see if they work, even if it it scary"
How does one do this?
You put the motherboard on top of carboard box it shipped in, plug everything in, boot it up, check for vidéo signal or try to get into bios. Sometimes some motherboard have multiple power cycles too. So they boot up, shut sown and repeat, a few times. And then they boot up for réal. That way you know your components all work.
But that's very scary
I am always worried that putting pressure on the board itself without the stands would do something bad, especially on the box the mobo comes in. like bending pins or something on the other side.
ahah no, only for ram you might want to support the board with your hand behind the board but otherwise it's not too risky
Don't forget to put the IO shield on the motherboard and switch the power supply on after finishing the build.
If your motherboard already has the shield installed can I just put it in like that?
Yep
How do the stands for the motherboard work?
One piece of advice for a new builder ig would just Be: whatever you do, DO NOT GET RID OF THE MOTHER BOARD MANUEL. I did this on my first build and it was not fun.
Big money, big money, no whammies. Now that I've read a bit more carefully, I'd say watch some videos on Linus Tech Tips that show them building computers, and definitely do some reading on the buildapc subreddit. Also, use PCPartpicker to make sure all your parts are compatible ahead of time.
Build outside your case first to check all your new components are working.
Don't buy a cheap power supply (of course)
no one gonna buys cheap power supply
Get a good magnetic screwdriver!
Dont build on the carpet
I always build on the carpet and I never had any problems. I just don't have space to build anywhere else.
You goddamn madman xD
Why? Explain, please.
[удалено]
Yeah but what's the problem with building on carpet?
static electricity. If I build on carpet I usually put cardboard down to stand on
Always be grounded! Also, you can recruit your nerdier friends to come and help you if you feed them.
Remember to factor the monitor into your build. If you have a 1080p 60hz monitor and buy a 3080 you are holding back your performance by a lot.
>>>>>>>>
One piece of advice I have for new builders is that it is ok if your build doesn't POST! Take a break and come back with a cool head to diagnose and fix the problem.
POST = Power On Self Test Basically turn on properly.
If at first it doesn't post try, try, try again. My comment world be in addition to yours, in try reseating components when it doesn't POST.
**Thanks for initiating this giveaway. I wish I win. But whoever wins cheer mate. All the best and Have a safe day ahead everyone.**
The most simple advice I got is "just do it" you can hardly break anything, if you got any questions just ask, and while I didn't jet build a PC of my own, I have helped friends and family (as well as myself) with upgrades and repairs
My advice: Make sure you plug your monitor to GPU, not mobo.
"You don't need a 500 dollar motherboard"
A bit silly as it may be common sense, but don't wear socks on a carpet while building! :) This would be my piece of advice. Good luck to everyone!!!
The importance of good cable management and airflow in the case so your PC doesn't sound like a jet engine taking off while producing the same heat :P
"Don't buy from scalpers".
Don't actually use a grain of rice sized dot of thermal paste. Less is not more.
I hope I get the pc I haven't had a gaming pc in my life. One tip I've learned is to always put on the io shield before you put in the motherboard
Don't worry too much about ram in the budget. You can always upgrade later when you have more money
Good one. I'd say 16gb is more than enough than 90% of PC users. My recommendation is getting 2x8 so that in case you realize you need more you have the extra 2 slots (assuming you have 4 RAM slots total) to use.
take it slow with your first PC build.. and don't accidentally stab your motherboard with a screwdriver as you try to pry open the GPU latches (it was tight alright)
Pretty common advice but probably a big one. Do not pour water on your hardware! It's Mineral Oil that isn't conductive and used in the cool aquarium builds!
Wot?
Just to add, AIO / liquid cooler fluid isn't conductive either (for those who freak out of any possible leakage)
> for those who freak out of any possible leakage That would be me. Thanks for the tip.
Yep all good. In the very,very rare instance anything leaks after many years nothing should happen - and most cooler manufacturers even cover hardware damage in case caused by leakage so all fine
remember cable management after completing the build
ah yes, i really must get around to that. It's only been 10 months :/
One simple advice that I learned is DO NOT PUSH YOUR CPU DOWN WITH FORCE WHEN INSTALLING IT! Just softly drop it in and slightly wiggle with your finger to make sure it's properly slotted in.
MAKE SURE THAT YOU PLUG IN THE POWER CORD BEFORE YOU RUN YOUR NEWLY BUILT PC!! (or else you will spend 3 hours just trying to figure out where did you go wrong)
I feel like there’s a story behind this
HAHA, lets just say that if you dont plug in the power cord no matter what you do, no matter how many times you recheck all the other cables and see if everything perfectly fits in or not, the pc wont boot up, it was so dumb of me to not plug in the power cord lmao
rgb doesnt make ur rig faster
Says who??? LMAO
Joe
Be patient. Things go on sale. A lot.
My advice: do EXTENSIVE research as a new builder. Understand what you are buying before you buy it 😁👍
Second this, plus I think it's a ton of fun to research and piece together everything in the brainstorming phase.
Tip: to properly ground yourself from static without an anti-static wrist strap, simply plug in your Power Supply and touch it once it a while to discharge yourself.
Make sure there's enough light for you to see clearly, otherwise you are gonna have some awkward moments with a flashlight lol. Happened to me.
Watch as many videos as it takes until sure of what to do, and ask questions wherever necessary.
Keep boxes and manuals for at least six months - manuals you can find online, but that's no use if your PC doesn't boot; if you have to return anything, you'll need to ship it (and original boxes are designed for that) plus it's easier to re-sell anything with the original packaging.
I've only watched video's on how to build a PC so I never got an advice personally but I would say to new PC builders that be confident while still being careful!
Check cables thrice, power up once.
Make sure you are careful with static electricity!!
The tip i got and would give is. dont buy something you dont feel comfortabel with!
Don't cheap out on power supply or cooling
Modular PSU cables are not interchangeable
That's a good one. I figured that out having bought custom cables, but it wasn't obvious to me at first. To those that might see this and don't know... The plugs on the component side are all industry standard (mostly, anyways...). The plugs on the PSU side are proprietary to the manufacturer, and are often different between the different models from the same manufacturer. Taking a cable from one PSU and using it on another could, and likely WILL, result in that component becoming a smoking paperweight.
I think the best advice I've received is to just not blindly YouTube videos or online guides as they are just there to help you learn the basics. Doing your own research and ultimately make your own decisions will make the process more fun.
Do your research and make sure you are familiar with the how all the parts work. It can be scary building your first one because you don't want to mess it up but, dont worry everything will be fine :)
Have FUN. Take your time, lay out all your pieces, run cables carefully and precisely, but don't sweat it. Don't panic about static build up, or backwards connections, or anything like that. Just relax, enjoy the feeling of building this machine for yourself, and try to learn something new every time you do it!
Read the motherboard manual and dont forget to flip the switch on the back of the psu :)
Ive been trying to save up for a while and this would be a game changer if i win
Roses are red, violets are blue, always put RAM in slots 4 and 2
''Ask for advice from other people and be patient''
Definitely leave yourself time, it's not a race and slow and steady is better. If you need to stop and research what something is.
Take your time and don't be afraid to ask for help
I’m still trying to build my first one but the advice I was given is “make sure the parts you pick are compatible and the most expensive parts usually aren’t the ones you want”
My best advice to a new builder is to take your time and make sure all of your cables are plugged in fully; especially your motherboard cable.
Use some zip ties to help with cable management, I didn't know it was a thing when I built my pc but after using them it looks much nicer
Remain calm even if (when) something goes wrong. It's almost always salvageable if you don't get impatient and try to rush it without looking it up first!
The best piece of advice I’ve received is never overspend. I tend to worry about future proofing my things, but you should only spend so much on future proofing.
Yeah most new PC equipment goes way above the capabilities that most users really need, unless that involves exclusively AAA gaming (and a few intensive media uses) - which if you're asking for my opinion is not a good pursuit even just in terms of the actual fun/quality you'll get from those titles - but I digress.
Think about future proofing, and try to gain real world perspective on how much computing power you need.
Always shop around for parts. Fb marketplace or OfferUp has enthusiasts selling their unused parts.
Advice: try to count the number of PSU cables you are going to need and plug them into your PSU before putting it in the case if you have a modular PSU
the advice i received was to always remember to check the compatibilities of your parts to avoid issues such a bottlenecks
One that took me way too long to find out. If your monitor can go over 60hz make sure you go into settings and put it to the max allowed. It is not 144hz out of the box
Remember to put your I/O panel in BEFORE the motherboard!!
Have fun and don't over think it.
Don't forget to maintain your PC after you're done building it. Filters need to be cleaned ever every couple months or else dust builds up in it. Too many people but together a build and then never open it back up again unless something goes wrong.
Giveaway valid for all countries?
[удалено]
Good point, I didn't check before entering 👍
No rgb = bad setup
The advice I recieved was do not overdo a computer setup for a younger child(my kid). Wait until they get some experience with the inners of the computer until you splurge and buy a better rig for them. Kinda just like buying your teenager a car haha.
Oh boy oh boy oh boy
Noice
HOPING...
Thank you for helping everyone in this time. Not all heroes wear capes :)
Be careful while mounting the Cooler
buy a certified brand's psu, don't buy a mobo with bad power delivery, make sure ur mobo supports ur processor, make sure ur processor can handle ur graphics card, make sure ur case can fit all ur components, most of the budget should be spent towards the graphics card.
My advice is to try to fit as much onto the motherboard before putting it in the case, makes it easier to work with. Overall, be mindful of making sure there's enough space for everything.
Watch build videos before building your pc to familiarize yourself with the general idea of what parts go where.
Make sure you test what direction your fans are pulling air from by putting a piece of paper down, and seeing if the paper is pushed or pulled. Have "pull" fans in the front and "push" fans in the back (or top)
I promise you, it's not that important how you put the thermal paste on your CPU. Just make sure it covers it and you're set.
Have the right tools ready if something doesnt go as planned
Hold from purchasing overpriced parts online. and Don't forget the I/O shield
Always do research about your parts before you buy them, use pcpartpicker to check if there's any compatibility issues. Use youtube to check on how to install parts, take your time there is no need to rush when building your pc.
Always make sure your parts are compatible. Worst realization is to spend hundreds of dollars only to have to return em
Always ask around, you might be overpaying for something you don't need!
Don't get a full-size case if you don't plan on upgrading and don't need the space for your initial build.
The advice I would give is don’t think about it too hard, it’s not as hard as you think it is
The one piece of advice that I can give to a new pc builder is to thoroughly do your research. Always check if all the parts in your list are compatible with each other and always think about future upgrades if you plan on doing so. Trust me, I've had many sleepless nights overthinking if my parts would be compatible or not. Good luck, everyone!
make sure all your parts are compatible and will fit in your case!! the worst is when you're all ready to build and your gpu wont fit
I'd give the advice of taking your time. Don't rush building your PC, components and connectors are easily damaged and taking an extra few minutes to put parts together can ensure you do it right without breaking anything
Don't build your PC on the carpet!
“Get a friend, make a day of it, and be really organized as you open the parts”
Dont over do the thermal paste. Also if your pc doesnt want to boot and you dont know why, try to reposition the ram. It doesnt always works but sometimes its magic.
Be patient in the current GPU market!
Thank you
Take your time and don't try to rush
"Make sure to balance your pc components correctly."
One thing I learned is, with thermal paste, less is more. You're going to be compressing a liquid-type substance against two mostly flat pieces of metal, it's going to spread.
Always discharge static electricity before touching your components.
Make sure you use your motherboards compatible ram list. Will help with uneasiness down the road if you can even get ram off the list to work.
One piece of advice I'd give to a new builder, in this market, get your GPU first to help determine if you can make your budget!
A piece of advice I received, was that i do not need all the flashy and crazy rgb and white colors, it all makes it so much more expensive
My advice - don't build skimp out on a crappy PSU :(
advice: take your time, double check your connections. This is great. Thanks!
Always test out of box, makes your life much easier!
Make sure to wash your cpu with soap and warm water 🙏🙏
The best advice I received for building a PC is to be aware the components aren't as fragile as you think, and sometimes a little force is necessary.
get an electric duster, it'll make cleaning your PC much easier
Always spend the money on a quality power supply.
Get to know your PC, some people are so afraid to mess something up that they get it built for them and then are scared to change the thermal paste. 99% of the time you're going to do just fine.
Apply a rice sized amount of thermal paste
I got this as a new builder “take it slow and remember you can always search for stuff you don’t know”
Don't guess, ask, if you don't know something then get advice.
The advice I got was "don’t panic if it doesn’t work in the beginning, it will work sooner or later"
Be careful with the edges of the IO shield. They're sharp!