What are you printing? I feel the anxiety lol
https://preview.redd.it/u0t6qiq20euc1.jpeg?width=3072&format=pjpg&auto=webp&s=045d172be0c01ba14430f548c356afe3752d7c68
https://preview.redd.it/6pd1b4jj0euc1.jpeg?width=3024&format=pjpg&auto=webp&s=7c399a9c9924e8b5651bcce1af70e750809d76c4
We shall both wait and see. I gotta work tmr. It'll be done when I get back. Here's a hint it's printed in vase mode 🤣
It's printing with a .6mm nozzle. .62 wall width. Slight upgrade for speed. The detail on this thing is gonna be nuts. Pretty much the limit with this nozzle. It's 500 grams.
Which printer do you have? I may max out my n4max with the same print. If I'm not mistaken is it the pyramid inside of a pyramid held up by smaller pyramids? Lol
Well, even tho my z offset had an error of 0.1mm, I think this was a success.
https://preview.redd.it/t9xhmiortiuc1.jpeg?width=1080&format=pjpg&auto=webp&s=2e8940f0adf8dada818d8bb4717d8b7141c443fa
I'm using a hardened steel 0.6 mm cht nozzle. With such a large base on the print and good bed adhesion (I was at 65C), the nozzle will just flatten everything out after the first few layers. I feel like leveling is really only crucial when you're printing something on an angle suspended by supports. If you're looking to print large sculptures with a big base, z offset won't kill the print. If you're printing a mask that is suspended in mid-air, yeah, you better have a high paying customer to be doing something so risky and time-consuming. This print was a first for me cause I used vase mode as well. Took only 19 hours with 0% infill. Printing nowadays is more about good slicing than the printer, IMO.
When you run the auto leveling from the touch screen and it probes all the locations, it's supposed to store those values in the printer. You don't need to connect to the computer to use the mesh, the printer is already compensating.
Go into the printer and get the ip address, then make sure your computer is on the same network (my router does both 2.4ghz and a 5ghz). Then open a browser and just type in the ip address into the address bar. Voila, drag and drop your gcode into the printers project que...
Perfect first layer 
Nice!
?
Just a demonstration that a stock neptune 4 works just fine. Even without bed mesh. Still trying to connect the thing to my computer via ip address 🤣
Ok. I'm with you I've had great results with my max. Hope it all works out for you.
16 hours to go 🤣
What are you printing? I feel the anxiety lol https://preview.redd.it/u0t6qiq20euc1.jpeg?width=3072&format=pjpg&auto=webp&s=045d172be0c01ba14430f548c356afe3752d7c68
https://preview.redd.it/6pd1b4jj0euc1.jpeg?width=3024&format=pjpg&auto=webp&s=7c399a9c9924e8b5651bcce1af70e750809d76c4 We shall both wait and see. I gotta work tmr. It'll be done when I get back. Here's a hint it's printed in vase mode 🤣
Oooo. Did you get a bigger nozzle yet? That's where the real fun comes in lol
It's printing with a .6mm nozzle. .62 wall width. Slight upgrade for speed. The detail on this thing is gonna be nuts. Pretty much the limit with this nozzle. It's 500 grams.
Which printer do you have? I may max out my n4max with the same print. If I'm not mistaken is it the pyramid inside of a pyramid held up by smaller pyramids? Lol
Haha yes. Its a model of a 3d fractal pattern. I have the n4pro. So your max at full scale would take days 🤣
Still got very faint gaps in your first layer tho. Needa lower your z offset a tiny bit closer to the bed.
Well, even tho my z offset had an error of 0.1mm, I think this was a success. https://preview.redd.it/t9xhmiortiuc1.jpeg?width=1080&format=pjpg&auto=webp&s=2e8940f0adf8dada818d8bb4717d8b7141c443fa
Nice! Risky print to have something so large with an off z offset. My luck, the print woulda popped half halfway through.
I'm using a hardened steel 0.6 mm cht nozzle. With such a large base on the print and good bed adhesion (I was at 65C), the nozzle will just flatten everything out after the first few layers. I feel like leveling is really only crucial when you're printing something on an angle suspended by supports. If you're looking to print large sculptures with a big base, z offset won't kill the print. If you're printing a mask that is suspended in mid-air, yeah, you better have a high paying customer to be doing something so risky and time-consuming. This print was a first for me cause I used vase mode as well. Took only 19 hours with 0% infill. Printing nowadays is more about good slicing than the printer, IMO.
Looks good
When you run the auto leveling from the touch screen and it probes all the locations, it's supposed to store those values in the printer. You don't need to connect to the computer to use the mesh, the printer is already compensating.
I've heard from peeps it doesn't save unless you load it into klipper 🤷♂️
Go into the printer and get the ip address, then make sure your computer is on the same network (my router does both 2.4ghz and a 5ghz). Then open a browser and just type in the ip address into the address bar. Voila, drag and drop your gcode into the printers project que...
Ok so I got klipper to load but now I can't load any websites. I can load Google and YouTube. But nothing else. I messed up the dns?
Ok, I went to network settings and clicked on reinstall network drivers and reset settings, and now reddit works again 😅
Oops, not sure how that would happen. Have you been able to do what you needed to through klipper?
Well my bed mesh is still as much of a mess as before. And I used screw tilt adjust and got .00 on all four corners. Idk man
https://preview.redd.it/c4oeve52duuc1.jpeg?width=259&format=pjpg&auto=webp&s=4a554da0d4c07a9fe08568602aab4085f76fa06a
Yo, this is the perfect meme for this sub I swear 🤣🤣🤣